Hydraulic seal manufacturer right now in 2024: Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications. Find even more details at rod seals manufacturer.
The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. See additional details on https://www.dmsseals.com/.
DMS Seals is a professional mechanical seals manufacturer and oil seal supplier for hydraulic seals, O-Rings, spring energized seals, oil seals, mechanical seal and so on. Hydraulic seals including step seals, glyd rings, guide strips, wiper seals, rod seals, piston seals, rotary seals, wear rings. We can provide the hydraulic seals with bronze filled PTFE, carbon filled PTFE, graphite filled PTFE, MoS2 filled PTFE, glass filled PTFE, virgin PTFE. About O-Rings, we can supply NBR, FKM, silicone, EPDM, HNBR, ACM, FFKM material.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
The O-ring of DMS SEALS is often used in hydraulic and pneumatic transmission systems and has wide applications. It can be used for both static and reciprocating seals. Moreover, it can also be used in rotary sealing systems. The O-ring can be installed in a groove with a rectangular cross section on the outer or inner circle, achieving a good sealing effect. It has many advantages compared with other types of sealing rings. Its compact structure makes it easy to assemble and disassemble. Moreover, its dynamic frictional resistance is relatively small, and a single piece of O-ring can achieve sealing performance in both directions.