Author: John Concrane

Dealerships charge more for work and parts than most different sorts of administration focuses. This is on account of a large portion of the professionals that dealerships have experienced years of costly preparing, have different affirmations and in this manner order a higher pay rate. Parts expenses are higher in light of the fact that they are utilized and also expansive industrial facility unique parts. A full tune up will regularly cost amongst $100 and $150 depending which dealership you take it to and what should be finished. A full tune up will comprise of the accompanying: changing and examining the start attachments and fitting wires, changing the air and fuel channels, conforming the planning, conceivable focuses and condenser change and fuel blend tuning.

Now therefore the step to be performed is to purge the old data and reset your ECU. Doing this allows it to adapt itself to new parts and efficiently perform post modification also. To reset the ECU you simply have to unplug the negative battery cable connection. Theoretically it is best to leave it in this disconnected condition for as long as you can. Practically leaving it disconnected overnight is more than enough. After having left the cable disconnected for sufficient time you have to connect back the cable. Start the car and keep it running so that it warms up. This would not take more than 10 minutes at the most in summers. Once you have done this you have accomplished the ECU resetting. Shut off the engine.

Tricks on Drakebox chip? To choose between a remap, replacement chip, new ECU or piggy back join our forum and discuss your options with our friendly members. In this article we shall focus on the specific act of “Chip tuning” and not dwell too much on remaps although both are very similar in nature. The term probably stems from the early days were chips could not easily be reflashed and updated. Now with some locked ECU’s chip removal and replacement is once again becoming an option. The only option in these cases was to literally replace the chip. Often these would need to be soldered and could be quite fiddly and, due to the delicate nature of chips, prone to failure. EPROMS which were erasable and programmable chips could be removed reflashed and reinserted into the car. Read additional info on Chip de Potencia Audi.

Does the chip tuning cause a higher level of wear on my engine? It can’t be denied that there is an additional load on the engine after the optimization. This additional load is still within the reserves stipulated by the manufacturer, though. An engine with chip tuning is an engine with lower safety reserves. So the vehicle must be warmed up and cooled down with great care. For the turbocharger, these processes are of paramount importance so it won’t be damaged by strong heat development. A higher boost automatically means more end speed of the turbocharger. Only through a higher speed of the turbine do you get more boost. It is therefore extremely important to stay within the turbine maps of the manufacturer and keep the safety functions in the engine software activated. This is the only way to ensure that the additional power remains stable in the long run and you can enjoy your engine for a long time. Does the chip tuning have to be entered in the vehicle documents? With chip tuning, we achieve a performance boost so the extra performance must be entered by TÜV. For many cars, we can offer you an entry in your vehicle documents. The cost of the entry varies according to vehicle type and engine type. Please just ask us. Do I get a guarantee on the chip tuning and my vehicle? We give the full BAR-TAK guarantee on our software optimization and work.

Manufacturers generally sell one vehicle that covers various markets, with different tax and emissions regulations; different climates with extremes of heat, cold, humidity; different fuel quantities; different operating altitudes, etc. A manufacturer has to take all of these factors into consideration and make substantial compromises in the vehicles operation. Sales and marketing also have a big affect on the way an engine is mapped. If you look the in manufacturer brochure at the engine specs, the torque graph will rise, then flatten out on a straight line, and then drop off. This obviously isn’t how an engine breathes, and it’s the request of sales and marketing to produce this flat lining of the torque.

I bought mine DAMOS for 100€ with complete ECU documentation in German…so many switches, limiters and maps that are not taught or even mentioned in basic remap guides – I found basic maps by myself but it took ages of reverse engineering and I still didn’t know what exactly each map is…with this Kamikaze style I made my first ECU remap. And if you think all is finally over because you have found DAMOS for your ECU…it is almost impossible to find or buy compressor maps for turbochargers. Sure there is lots of maps around but each car, manufacturer, even engine has different turbo with different parameters such as trim and A/R . Skoda Octavia 2 vRS 2.0TDi PPD engine has got Garrett GT1749V, Golf too…yet each may have different turbo parameters. Read more details at Chip Tuning Peugeot.