Month: February 2020

Top welding guides: For the best control of your weld bead, keep the wire directed at the leading edge of the weld pool. When welding out of position (vertical, horizontal or overhead welding), keep the weld pool small for best weld bead control, and use the smallest wire diameter size you can. A bead that is too tall and skinny indicates a lack of heat into the weld joint or too fast of travel speed. Conversely, if the bead is flat and wide, the weld parameters are too hot or you are welding too slowly. Ideally, the weld should have a slight crown that just touches the metal around it. Keep in mind that a push technique preheats the metal, which means this is best used with thinner metals like aluminum. On the other hand, if you pull solid wire, it flattens the weld out and puts a lot of heat into the metal. Finally, always store and handle your filler metals properly. Keep product in a dry, clean place — moisture can damage wire and lead to costly weld defects, such as hydrogen-induced cracking. Also, always use gloves when handling wires to prevent moisture or dirt from your hands settling on the surface. When not in use, protect spools of wire by covering them on the wire feeder, or better yet, remove the spool and place it in a clean plastic bag, closing it securely.

As you can already tell from the title, it has more features and accessories compared to its predecessor in this list. It is very lightweight, powerful, versatile and compact. These are the four best words to describe it. It has a lift detector system, rear mounted control and gravity feed system where the HMD904S coolant bottles are stored. The coolant help reduce heat build especially when you are performing a heavy-duty assignment. It comes with a three-year warranty meaning the manufacturers assures of quality service from this tool.

Calibration gas cylinder online shopping UK: Helium / argon mixtures are sometimes used for their higher heat characteristics. Gas mixtures, usually 25% helium and 75% argon are sometimes used and can help to increase travel speeds when AC – gas tungsten arc welding. Mixtures of more than 25% helium for AC – gas tungsten arc welding are used, but not often, as they can tend to produce instability, under certain circumstances, in the AC arc. Pure helium or high percentages of helium (He-90%, Ar-10%) shielding gas are used primarily for gas tungsten arc machine welding with direct current electrode negative (DCEN). Often designed as seam welders, the combination of GTAW – DCEN and the high heat input from the gas used can provide fast welding speeds and outstanding penetration. This configuration is sometimes used to produce full penetration butt welds, welded from one side only, onto temporary baking with no vee-groove preparation, just a square edged plate.

Several tips on welding equipment, MIG and TIG welders, plasma cutters. MIG welders use a wire welding electrode on a spool that is fed automatically at a constant pre-selected speed. The arc, created by an electrical current between the base metal and the wire, melts the wire and joins it with the base, producing a high-strength weld with great appearance and little need for cleaning. MIG welding is clean, easy and can be used on thin or thicker plate metals. Similar to MIG welding, flux-cored arc welding (FCAW)* is a wire-feed process but differs in that self-shielded flux-cored welding does not require a shielding gas. Instead, flux-cored wire is used to shield the arc from contamination. This is a simple, efficient and effective welding approach, especially when welding outdoors, in windy conditions or on dirty materials. The process is widely used in construction because of its high welding speed and portability. See additional details on Welding Equipment.

Mag drill reviews: In order to find a worthy investment, one has to get familiar with the do’s and don’ts. However, most people decide to skip that particular step and invest in the first thing they find interesting. Sadly, that strategy usually ends up with you buying something that doesn’t meet your expectations or overpaying something you could get for less money. Either way, it’s essential for every serious buyer to go through some of the tips and tricks of drill shopping in order to get the best possible deal. Keep these tips in mind and you’ll more than likely find a good model for yourself.

If you have been in the industry for any length of time, you will know the most common examples. This includes the likes of argon, helium, or carbon dioxide. Each gas offers its own unique properties when welding, and a case could be made for any of them. Carbon dioxide, for example, is low cost. It also makes for inferior welds, letting too much oxygen in. Argon, on the other hand, might be the perfect replacement.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding. Read a few more details at https://www.weldingsuppliesdirect.co.uk/.